Motorcycle Lift - Printable Version
+- Newell Gurus (https://newellgurus.com)
+-- Forum: Technical Discussions (https://newellgurus.com/forumdisplay.php?fid=3)
+--- Forum: Towing (https://newellgurus.com/forumdisplay.php?fid=31)
+--- Thread: Motorcycle Lift (/showthread.php?tid=3955)
+- Newell Gurus (https://newellgurus.com)
+-- Forum: Technical Discussions (https://newellgurus.com/forumdisplay.php?fid=3)
+--- Forum: Towing (https://newellgurus.com/forumdisplay.php?fid=31)
+--- Thread: Motorcycle Lift (/showthread.php?tid=3955)
RE: Motorcycle Lift - bikestuff - 12-29-2017
Dario,
The lift will come off easily (With a forklift to hold the weight)..but there are two brackets welded to frame. Not so easy to remove and keep. A call to hydralift would tell you if its easy to buy new brackets.
The new model that was put on after the incident has a two piece ramp rather than the old one piece ramp but other than that...its pretty much the same as the old one.
Thanks for the compliment on the bike...I just replaced that one with a 2018 version. The new one has a digital dash display which is HUGE improvement over the old gauges that I could not read from a normal sitting (or standing) position on the bike. You were correct about not touching the bike during “the incident”. I could not believe that the entire lift was broken without even scratching the bike. The lightpost was in exactly the right place.
Bill
RE: Motorcycle Lift - encantotom - 12-29-2017
bill.....standing position? you are one of those guys?
tom
RE: Motorcycle Lift - Dallas2254 - 09-17-2018
Just added a Hydralift to my 2004 coach. Was pretty easy one day project. Hardest part was cutting the notches out of the lower part of the engine door but after a few geometric calculations and aligning the angle of closure, I used my saber saw and managed to cut just once and now I have two pieces that could easily be glassed back in if I were to take the lift off the back.
Was able to just bolt the lift to the existing frame mounts for the 20,000 lb trailer hitch that was bolted up to the frame that I removed and used the same bolt holes to mount the hydralift. No welding required
RE: Motorcycle Lift - encantotom - 09-18-2018
nice work looks great
tom
RE: Motorcycle Lift - pairodice - 09-18-2018
That lift is very cool and I like the way it folds up closer to the coach. My old lift (overbilt) used a starter motor to lift and I remember several times having to whack it with a hammer (or pray) in order to get it to lift the bike... I had it rebuilt and it solved the issue... I like the hydraulic idea though. Now all I need is a BIKE! I miss my KTM 950 adventure!
RE: Motorcycle Lift - Fulltiming - 09-18-2018
Great installation job Dallas.
RE: Motorcycle Lift - Deper10 - 09-19-2018
(09-17-2018, 10:35 PM)Dallas2254 Wrote: Just added a Hydralift to my 2004 coach. Was pretty easy one day project. Hardest part was cutting the notches out of the lower part of the engine door but after a few geometric calculations and aligning the angle of closure, I used my saber saw and managed to cut just once and now I have two pieces that could easily be glassed back in if I were to take the lift off the back.
Was able to just bolt the lift to the existing frame mounts for the 20,000 lb trailer hitch that was bolted up to the frame that I removed and used the same bolt holes to mount the hydralift. No welding required
Great looking installation. Can you still open the rear cover with the lift in place?
Dario
RE: Motorcycle Lift - bikestuff - 09-19-2018
With mine, I have to lower the lift (with bike still on) to allow the door to swing open. Also, because of where the controller plugs in....I have to lower the lift, then remove controller, then open door.
I really like how Dallas cut the slots. Mine has an entire piece of fiberglass removed. His install is much neater.
Bill
RE: Motorcycle Lift - DanB - 09-19-2018
Hydralift's are the Bomb Diggity. A friend of mine had one installed on his Monaco Signature.
RE: Motorcycle Lift - Dallas2254 - 11-05-2018
(09-19-2018, 05:25 AM)Deper10 Wrote:(09-17-2018, 10:35 PM)Dallas2254 Wrote: Just added a Hydralift to my 2004 coach. Was pretty easy one day project. Hardest part was cutting the notches out of the lower part of the engine door but after a few geometric calculations and aligning the angle of closure, I used my saber saw and managed to cut just once and now I have two pieces that could easily be glassed back in if I were to take the lift off the back.
Was able to just bolt the lift to the existing frame mounts for the 20,000 lb trailer hitch that was bolted up to the frame that I removed and used the same bolt holes to mount the hydralift. No welding required
Great looking installation. Can you still open the rear cover with the lift in place?
Dario
Yes, I can open the engine cover with the motorcycle on it but lowered to the ground
Dallas